DIY hang system for DS-dolls
Moderator: jiayi
DIY hang system for DS-dolls
as posted in my Leora thread, I have developed a system to hang the dolls with head on.
CAUTION: only tested with DS145 / sKayla head, the prototype with thread rod bonded(!) into a tube took 30 kg . Please, test your assembly before using it on your doll.
What do we need:
1 - Tool to cut metric M6 thread
2 - threaded rod M3 (steel), length tbd
3 - Eyebolt M6 x 25 mm (stainless steel preferred)
4a - 2x standoff M3 (Aluminum, used in electronics to raise PCBs)
5 - Connection nut M6 (stainless steel)
Thread lock (Loctite)
I also use a shackle 6 mm (stainless steel) which is rated up to 50 kg load
First step is to cut M6 thread to the outside of both standoffs as long as you can get.
Result should look like part 4b
Bolt one of the standoffs to the threaded rod using thread lock. Determine the length of the thread rod by measuring the distance from the neck bolt to the top of the head and add what you need up to your hanging support (minus the upper part (4B, 5, 3))
Bolt the other standoff to one side of the conection nut M6 using thread look. Take care the thread ends at the center of the nut.
I cut off the remaining length, but this is not necessary
Bolt the eyebolt to the other end of the connection nut. Useage of thread lock is up to you (I don't)
You should have now 2 parts:
The lower part in the picture goes to the neck bolt of the doll, then put on the head and wig (that needs some experience ) and then bolt on the upper part from the picture.
Without the doll it should look like that:
If you want to use the shackle mentioned earlier, you hav to drill the hole in the eyebolt to 7mm diameter, otherwise the narrower side of the shackle wont fit.
I will use some shrinking tiube to protect the treaded rod from the cross pin in the head tube.
I will add a counter nut M3 to the top part to prevent rotating.
An improvement might be to replace the aluminum standoffs by steel ones.
The eyebolt can also be used for hanging the doll for storage when mounted to the neck bolt directly (I use this for showering, thus I dont use threadlock).
My appartment has a wooden ceiling installed by the previous owner, so I do not know what load it can take.
I found a different solution for that:
It is rated to take up to 90 kg of load, width between floor beam and gallows is 1,72 meters.
Next will be to get a height adjustment system, to the gallows.
If there are any questions feel free to ask...
GirlsGang
Someone who thinks logically is a nice contrast to the real world.
The girls:
Leora & Leonie (DS145)
Ebony & Ivory (Smart Dolls, 1/3)
Meet the Gang (1/6)
REVIEW:
AI S+ Fay/Sonia 4woods EU
- siliconefun
- Doll Guru
- Posts: 5359
- Joined: Sun May 13, 2012 12:21 pm
- Location: Luxembourg - The Land of the Red Rocks -
- Contact:
Re: DIY hang system for DS-dolls
your DIY hang system tutorial for DS-dolls is well done and surely as good as the original one.
Guy
Re: DIY hang system for DS-dolls
awesome. thx for sharing!
/g'day.
Want to see more shots of me ladies?...Head to: The Doll Album | The K TEAM Thread | Karamina's Thread | The Kyanna Project
- deadpringle
- Doll Elder
- Posts: 3022
- Joined: Sun Jul 15, 2012 10:31 pm
- Location: United States
- Contact:
Re: DIY hang system for DS-dolls
I used to hang my first DS doll, but I stopped. Since I'm with her practically all the time when I'm home, I found that getting her down off the hook was a hassle. Now, I just store my dolls in my doll room sitting on soft chairs.
Abed: About to...
Troy: Eat garbage dip!... WHY DID I HAVE TO GO THIRD?!
-- from Community - Season 4 Episode 5
Re: DIY hang system for DS-dolls
Main use for the hang system will be fotography
GirlsGang
Someone who thinks logically is a nice contrast to the real world.
The girls:
Leora & Leonie (DS145)
Ebony & Ivory (Smart Dolls, 1/3)
Meet the Gang (1/6)
REVIEW:
AI S+ Fay/Sonia 4woods EU
-
- Active Member
- Posts: 189
- Joined: Sat Nov 16, 2013 2:30 am
- Contact:
Re: DIY hang system for DS-dolls
hi @girlGangGirlsGang wrote:Hi,
as posted in my Leora thread, I have developed a system to hang the dolls with head on.
CAUTION: only tested with DS145 / sKayla head, the prototype with thread rod bonded(!) into a tube took 30 kg . Please, test your assembly before using it on your doll.
What do we need:
1 - Tool to cut metric M6 thread
2 - threaded rod M3 (steel), length tbd
3 - Eyebolt M6 x 25 mm (stainless steel preferred)
4a - 2x standoff M3 (Aluminum, used in electronics to raise PCBs)
5 - Connection nut M6 (stainless steel)
Thread lock (Loctite)
I also use a shackle 6 mm (stainless steel) which is rated up to 50 kg load
First step is to cut M6 thread to the outside of both standoffs as long as you can get.
Result should look like part 4b
Bolt one of the standoffs to the threaded rod using thread lock. Determine the length of the thread rod by measuring the distance from the neck bolt to the top of the head and add what you need up to your hanging support (minus the upper part (4B, 5, 3))
Bolt the other standoff to one side of the conection nut M6 using thread look. Take care the thread ends at the center of the nut.
I cut off the remaining length, but this is not necessary
Bolt the eyebolt to the other end of the connection nut. Useage of thread lock is up to you (I don't)
You should have now 2 parts:
The lower part in the picture goes to the neck bolt of the doll, then put on the head and wig (that needs some experience ) and then bolt on the upper part from the picture.
Without the doll it should look like that:
If you want to use the shackle mentioned earlier, you hav to drill the hole in the eyebolt to 7mm diameter, otherwise the narrower side of the shackle wont fit.
I will use some shrinking tiube to protect the treaded rod from the cross pin in the head tube.
I will add a counter nut M3 to the top part to prevent rotating.
An improvement might be to replace the aluminum standoffs by steel ones.
The eyebolt can also be used for hanging the doll for storage when mounted to the neck bolt directly (I use this for showering, thus I dont use threadlock).
My appartment has a wooden ceiling installed by the previous owner, so I do not know what load it can take.
I found a different solution for that:
It is rated to take up to 90 kg of load, width between floor beam and gallows is 1,72 meters.
Next will be to get a height adjustment system, to the gallows.
If there are any questions feel free to ask...
i would like to write a post about your excellent tip.
Are you ok that i used your pics?
Re: DIY hang system for DS-dolls
I dont get your point...
Where do you want to write a post?
This thread is not in the "members only" section so you can link it.
However, as long as you state that the pics and tips are not yours, I am okay.
GirlsGang
Someone who thinks logically is a nice contrast to the real world.
The girls:
Leora & Leonie (DS145)
Ebony & Ivory (Smart Dolls, 1/3)
Meet the Gang (1/6)
REVIEW:
AI S+ Fay/Sonia 4woods EU
Re: DIY hang system for DS-dolls
As you may have noticed I have covered the threaded rod with (heat) shrinking tube.
Pics of Leora using the hang system will be found in her introduction thread (link in my signature)
GirlsGang
Someone who thinks logically is a nice contrast to the real world.
The girls:
Leora & Leonie (DS145)
Ebony & Ivory (Smart Dolls, 1/3)
Meet the Gang (1/6)
REVIEW:
AI S+ Fay/Sonia 4woods EU
Re: DIY hang system for DS-dolls
GirlsGang
Someone who thinks logically is a nice contrast to the real world.
The girls:
Leora & Leonie (DS145)
Ebony & Ivory (Smart Dolls, 1/3)
Meet the Gang (1/6)
REVIEW:
AI S+ Fay/Sonia 4woods EU
- von_Shredhead
- Doll Guru
- Posts: 5561
- Joined: Tue Mar 06, 2012 7:34 pm
- Location: Third Rock From The Sun
- Contact:
Re: DIY hang system for DS-dolls
Cheers!
Nina's Thread - Doll Sweet 145cm
Lila's Thread - Doll Sweet 145cm
Heather's Thread - 4Woods Allure
Sativa's Thread - Virgin Rose Kelu
Naomi's Thread - 1AM WM125
"Build a man a fire, and he'll be warm for a day. Set a man on fire, and he'll be warm for the rest of his life."
- deadpringle
- Doll Elder
- Posts: 3022
- Joined: Sun Jul 15, 2012 10:31 pm
- Location: United States
- Contact:
Re: DIY hang system for DS-dolls
Abed: About to...
Troy: Eat garbage dip!... WHY DID I HAVE TO GO THIRD?!
-- from Community - Season 4 Episode 5
Re: DIY hang system for DS-dolls
Re: DIY hang system for DS-dolls
thank you for pointing that out again.
It is really a must to test before use.
I should have written that in bold and red
GirlsGang
Someone who thinks logically is a nice contrast to the real world.
The girls:
Leora & Leonie (DS145)
Ebony & Ivory (Smart Dolls, 1/3)
Meet the Gang (1/6)
REVIEW:
AI S+ Fay/Sonia 4woods EU
Re: DIY hang system for DS-dolls
I'm looking at getting this eyebolt to hang my 145cm body for storage: http://www.amazon.com/Stainless-Steel-M ... B009CZ4MTE
Just confirming that 25mm is the correct thread length size.
Also, if I went ahead and made a similar head-through bolt system, would this kit have the correct thread size? http://www.harborfreight.com/21-pc-carb ... 61398.html
Or would I need a metric tap&die threading kit specifically? I wasn't able to figure out M6 in non-metric terms, and I don't know what the internal threading of the DS neck is in US units.