1/3 scale 3D printed head
Moderator: LoneRanger
- carlys_guy
- Doll Oracle
- Posts: 8594
- Joined: Sun Oct 26, 2014 10:55 am
- Location: northeast USA
- Contact:
1/3 scale 3D printed head
the picture is of a 3D printed 1/3 scale head from thingiverse.
https://www.thingiverse.com/thing:3311141
carlys_guy
- Endless War
- Doll Elder
- Posts: 2999
- Joined: Wed Nov 08, 2017 2:16 am
- Location: Chancellor at iNORGANIC ACADEMY
- Contact:
- carlys_guy
- Doll Oracle
- Posts: 8594
- Joined: Sun Oct 26, 2014 10:55 am
- Location: northeast USA
- Contact:
Re: 1/3 scale 3D printed head
https://www.thingiverse.com/thing:3495928
been thinking of getting a 3D printer for a while just don't know if i could make it work.
carlys_guy
Re: 1/3 scale 3D printed head
However there is always a lot of head scratching/hair tearing with any new techie thing
- justintime
- Doll Patriarch
- Posts: 4383
- Joined: Thu Mar 10, 2016 8:19 pm
- Location: Exploring the Blue Planet from 100M down
- Contact:
Re: 1/3 scale 3D printed head
I have the same thoughts.
- Mishka1965
- Doll Elder
- Posts: 3377
- Joined: Wed Jan 21, 2015 11:37 pm
- Location: USA California
- Contact:
Re: 1/3 scale 3D printed head
2018-2021 Photographing for JIUSHENG-DOLL,6YE,SinoDoll
2022-2023 Photographer/Reviewer for Zelex, TAYU, MRD and IronTech
Twitter Page: https://twitter.com/Mishka_1965
Instagram Page:https://www.instagram.com/_mishka1965_/
- justintime
- Doll Patriarch
- Posts: 4383
- Joined: Thu Mar 10, 2016 8:19 pm
- Location: Exploring the Blue Planet from 100M down
- Contact:
Re: 1/3 scale 3D printed head
- carlys_guy
- Doll Oracle
- Posts: 8594
- Joined: Sun Oct 26, 2014 10:55 am
- Location: northeast USA
- Contact:
Re: 1/3 scale 3D printed head
@ justintime i haven't decided between a creality ender 3 pro or an alfawise u30. the ender 3 and alfawise both have the same build volume. you can get the ender 3 lots of places like amazon and matterhackers, it seems the alfawise is only available from gearbest in china.
carlys_guy
Re: 1/3 scale 3D printed head
https://community.ultimaker.com/topic/1 ... esolution/
The theoretical maximum resolution of the z axis is much higher then you'll ever be able to achieve in practice... I think the z axis is technically capable of about 0.005mm resolution in theory (the distance of a single step on the motor), but getting reliable and precise extrusion to work without too much back-pressure below about 0.04mm is very difficult. I typically print at 0.08mm per layer, but I have managed to do 0.04 myself in the past and I've seen others achieve this. I've heard rumour of people going as low as 0.02, but that's really pushing it and I can't recall where I've seen that mentioned or if they had any success at that.
There is a noticeable difference between 0.1 and 0.08, but even at 0.1 the detail you can get is incredible. You have to look really closely to see the layers.
Re: 1/3 scale 3D printed head
It takes very little finishing to get a PLA surface smooth to the touch
Re: 1/3 scale 3D printed head
If you print ABS, you can put it in an acetone chamber to smooth the surface. Really, really smooth, like injection mold.seagull wrote:0.08mm is about the thickness of a strand of human hair.
It takes very little finishing to get a PLA surface smooth to the touch