Meet EVA, my new mannequin to mod!
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
- MannequinFan
- Vendor Affiliated
- Posts: 4720
- Joined: Wed Jan 04, 2012 8:58 pm
- Location: Central Illinois, U.S.
- Contact:
Re: Meet EVA, my new mannequin to mod!
Nice detail on the tongue. What kind of paint do you use for your work?
My Blog-> mfcreations3d.blogspot.com ... Easy Move Eyes™
My Shapeways Shop-> shapeways.com/shops/mf-creations
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
- rubherkitty
- Doll Oracle
- Posts: 8966
- Joined: Sat Aug 25, 2012 5:24 pm
- Location: Interstate 44 with 10 long-haired Friends a' Jesus In a chartreuse micra-bus
- Contact:
Re: Meet EVA, my new mannequin to mod!
Thanks for the kind offer, but I think even the tips from these hands will be too big.Fiberglass guy wrote:I have 2 pairs of hands available from old MQ's One has fingernail extensions added but they could be easily removed, fit standard MQ's and have standard attachment points, off of the same one MF used for Sammi and The MZ-vis2 if you need to see what they look like..
Nikki's hands are a little less than 13cm long from the wrist joint to tip of the middle finger. Largest nail is around 6mm wide.
I'll just have to drill the finger tips and glue in a wire loop for a armature and add some bondoglass on the ends. No great hurry at the moment. Her fingers really exhibit no specific joints so adding length will not disrupt any joint pattern. As she already has fingernails, I may just cut the tips off behind the nail and extend them out w/a threaded rod running down the center then all I have to do is fill in the gap.
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
- MannequinFan
- Vendor Affiliated
- Posts: 4720
- Joined: Wed Jan 04, 2012 8:58 pm
- Location: Central Illinois, U.S.
- Contact:
Re: Meet EVA, my new mannequin to mod!
I'm thinking of doing something similar to the magnetic leg attachment for the arms.
I would 3d print a cup that would go over the existing arm hook - probably about 2-3/4" diameter. The cup would have a magnet in the end just like the leg idea. The cup would then fit into a printed socket that would be epoxied to the body. The 3" diameter hole would be just about the right size for the socket.
This would at least keep the arms from falling off when she's laying down and give her a small amount of posability.
My Blog-> mfcreations3d.blogspot.com ... Easy Move Eyes™
My Shapeways Shop-> shapeways.com/shops/mf-creations
-
- Senior Member
- Posts: 243
- Joined: Sat Sep 20, 2014 4:02 pm
- Contact:
Re: Meet EVA, my new mannequin to mod!
- MannequinFan
- Vendor Affiliated
- Posts: 4720
- Joined: Wed Jan 04, 2012 8:58 pm
- Location: Central Illinois, U.S.
- Contact:
Re: Meet EVA, my new mannequin to mod!
After I get Eva's adapter printed I'll do some tests for the arm and leg attachments to make sure they will work.Fiberglass guy wrote:I would be interested in those for eva! or even universal ones, I will use my bungee method, over magnets, would just need a cup and socket assembly
Here is how the new V3 adapter design is looking on Eva.
When the flange is feathered out with Apoxie I think it will look more natural...
My Blog-> mfcreations3d.blogspot.com ... Easy Move Eyes™
My Shapeways Shop-> shapeways.com/shops/mf-creations
- MannequinFan
- Vendor Affiliated
- Posts: 4720
- Joined: Wed Jan 04, 2012 8:58 pm
- Location: Central Illinois, U.S.
- Contact:
Re: Meet EVA, my new mannequin to mod!
Kind of reminds me of a flower opening its petals... Would also make a nice beer pitcher if it were bigger.
My Blog-> mfcreations3d.blogspot.com ... Easy Move Eyes™
My Shapeways Shop-> shapeways.com/shops/mf-creations
- rubherkitty
- Doll Oracle
- Posts: 8966
- Joined: Sat Aug 25, 2012 5:24 pm
- Location: Interstate 44 with 10 long-haired Friends a' Jesus In a chartreuse micra-bus
- Contact:
Re: Meet EVA, my new mannequin to mod!
How many pieces is it assembled from?
Would you say the location is a happy medium between V & A entry?