eye bulging out
eye bulging out
The right eye bulging, too but not so extreme.
Re: eye popping out
Re: eye popping out
Ok, I`ll post a picture, soon.
BTW the right eye is bulging out, too, but not so extreme like the left. But everytime when she does a bj I have to push her eyes back. Ok, but still better than a unlucky married man.
Re: eye bulging out
I've been married 30 years myself. To date both eyes are still in her head...
- Dollpimp2018
- Doll Advisor
- Posts: 873
- Joined: Sat Jun 30, 2018 7:06 am
- Contact:
Re: eye bulging out
IronTech Victoria Unboxing Video https://vimeo.com/305089873
AmorDoll Bianca Unboxing Video https://vimeo.com/298682320
Re: eye bulging out
- Marianne wm157b/head 159 from BCD ❤❤❤
Favorite song or mix atm, this change in a heartbeat.
- Dollyman25442
- Doll Mentor
- Posts: 1445
- Joined: Fri Aug 11, 2017 11:30 pm
- Contact:
Re: eye bulging out
A quicker and easier fix is to simply remove the head and drill a 3/8ths hole in the base of her skull just to the side of where her head connector stud is located. This will relieve the pressure and cure the bulging eye but sadly it won't do shit to improve the overly tight oral canal. It'll still be like fucking a pinhole. But the eyes won't bulge anymore, lol.
- YojimBeau
- Active Member
- Posts: 116
- Joined: Thu Aug 16, 2018 2:27 pm
- Location: Oklahoma, USA
- Contact:
Re: eye bulging out
Diagram, illustration, picture or link, please? How deep a hole is needed?Dollyman25442 wrote:A quicker and easier fix is to simply remove the head and drill a 3/8ths hole in the base of her skull just to the side of where her head connector stud is located. This will relieve the pressure and cure the bulging eye but sadly it won't do shit to improve the overly tight oral canal. It'll still be like fucking a pinhole. But the eyes won't bulge anymore, lol.
- Dollyman25442
- Doll Mentor
- Posts: 1445
- Joined: Fri Aug 11, 2017 11:30 pm
- Contact:
Re: eye bulging out
None of the above needed.YojimBeau wrote:Diagram, illustration, picture or link, please? How deep a hole is needed?Dollyman25442 wrote:A quicker and easier fix is to simply remove the head and drill a 3/8ths hole in the base of her skull just to the side of where her head connector stud is located. This will relieve the pressure and cure the bulging eye but sadly it won't do shit to improve the overly tight oral canal. It'll still be like fucking a pinhole. But the eyes won't bulge anymore, lol.
It's not a depth hole, it's a through hole through the fiberglass skull at the base right next to where the neckbolt is. Takes about 30 seconds to do.
Re: eye bulging out
But does the skin sliding then in the hole? Could this lead to a tear?
A picture would be very helpful, where exactly we have to drill the hole.
How deep and which diameter?
- Dollyman25442
- Doll Mentor
- Posts: 1445
- Joined: Fri Aug 11, 2017 11:30 pm
- Contact:
Re: eye bulging out
Not sure I can describe this any better but here goes.J90 wrote:Great idea!
But does the skin sliding then in the hole? Could this lead to a tear?
A picture would be very helpful, where exactly we have to drill the hole.
How deep and which diameter?
Remove the head.
Turn it upside down.
You should now be looking at the M16 head connector bolt.
One inch to either side of that bolt, drill ONE 3/8ths hole all the way through the fiberglass skull. The skull is hollow. Drilling all the way through should take all of 30 seconds.
You are done. Re-attach head.
Now you have a hole in which pressure is relieved when you insert something in the mouth and as a result, the eyes won't bulge.
Re: eye bulging out
Re: eye bulging out
Dollyman25442 wrote:Not sure I can describe this any better but here goes.J90 wrote:Great idea!
But does the skin sliding then in the hole? Could this lead to a tear?
A picture would be very helpful, where exactly we have to drill the hole.
How deep and which diameter?
Remove the head.
Turn it upside down.
You should now be looking at the M16 head connector bolt.
One inch to either side of that bolt, drill ONE 3/8ths hole all the way through the fiberglass skull. The skull is hollow. Drilling all the way through should take all of 30 seconds.
You are done. Re-attach head.
Now you have a hole in which pressure is relieved when you insert something in the mouth and as a result, the eyes won't bulge.
- Dollyman25442
- Doll Mentor
- Posts: 1445
- Joined: Fri Aug 11, 2017 11:30 pm
- Contact:
Re: eye bulging out
I'm sorry your'e not understanding this modification.J90 wrote:Thank you. But doesn`t the skin of the head slide in the hole when pressure is relieved? This could probably lead to a tear. And then the fluid (water, lube,...) in the mouth would drips in the body, which leads to mold.
Dollyman25442 wrote:Not sure I can describe this any better but here goes.J90 wrote:Great idea!
But does the skin sliding then in the hole? Could this lead to a tear?
A picture would be very helpful, where exactly we have to drill the hole.
How deep and which diameter?
Remove the head.
Turn it upside down.
You should now be looking at the M16 head connector bolt.
One inch to either side of that bolt, drill ONE 3/8ths hole all the way through the fiberglass skull. The skull is hollow. Drilling all the way through should take all of 30 seconds.
You are done. Re-attach head.
Now you have a hole in which pressure is relieved when you insert something in the mouth and as a result, the eyes won't bulge.
As such, I think it best you try something other than the mod I've suggested.
Good luck!
Re: eye bulging out
But I think I understand what you mean. Drilling a hole through the skull (not the skin of the mouth). By pressure the skin of the mouth will slide a little bit in the hole. But I`m adraid that the sharp hole could lead to a tear.