R cup 168 babe versus a real man

DollNFuture · Post by **DollNFuture** » Mon Apr 01, 2019 7:53 pm

Hi folks forgive me if this has been discussed but I could not find a thread that discussed it in detail with detailed answers. My question is about the ability of the awesome high-quality Sanhui 168 cm R cup babe to accommodate her real man.

Let us say for example, hypothetically, to explore maximums of a doll's capability, that a guy has got a member that is 9 inches long and let's say 2 inches in diameter. That will make him a circumference of about 6 inches. Note that I'm talking circumference. So how does a guy like that possibly fit himself into his new girlfriend?

I realize the silicone stretches, but I see on some threads many issues with tearing and I'm wondering if the doll could accommodate that kind of size in the first place?

Anung Un Rama · Post by **Anung Un Rama** » Mon Apr 01, 2019 8:40 pm

These gals are tight, so if you wish to not damage her, go easy and plenty of good water based lube, just like with a real gal, but she wont loosen up half way through without there being damage.

The sanhuis have a separate laminated silicone vaginal cavity, so separation can occur if to vigorous.

As far as length, yep, probably bottom out, but this also happens with organic gals too right!

Anung

DollNFuture · Post by **DollNFuture** » Tue Apr 02, 2019 3:00 pm

Sounds like this is an incompatible situation! Since she does not stretch like a real girl, could be lots of damage it sounds. When I say "real man" I mean similar to when people say "real girl" vs a doll girl....RG and RM...

Somewhere I read that silicone stretches 425%. If she is laminated does that mean the silicone is really thin and not performing a stretch like the rest of the body?

Anung Un Rama · Post by **Anung Un Rama** » Tue Apr 02, 2019 8:06 pm

Merely providing feedback from a previous topic shown de-lamination on a similar model. It alludes me for now, and perhaps this was merely a a production flaw at the time, that has now been corrected.

generally, sure, if two different silicone blends are used, there is a possibility that they will have different properties.

Most likely the vag layer was designed to be softer, and as such would not likely possess the same firmness or resilience as say a high stress joint area like the groin for example.

The trade off would be use the same blend through out, but then the pussy may feel like shagging a tire (well not exactly a tire, merely an analogy, but it would be a lot firmer).

Anung

DollNFuture · Post by **DollNFuture** » Fri Apr 05, 2019 4:31 pm

This sounds like a losing proposition for a good fit. The insert from a well-known American manufacturer in California starts with a dimension of 7" length x 2" in diameter and stretches to 12" x 4" in diameter which is very large range. It sounds like the sanhui will not accommodate.

Anung Un Rama · Post by **Anung Un Rama** » Fri Apr 05, 2019 9:31 pm

you can always request custom sizes by contacting SANHUI direct, you just need to be patient as they can be slow with correspondence so use both email, skype and even PM function here to get their attention.

Anung

DollNFuture · Post by **DollNFuture** » Sat Apr 06, 2019 5:34 pm

I may have already asked this in another post so forgive me if I repeat myself but on Sanhui's site is the measurements page for the babe it says the "girth" is 1.3 inches. Surely what they really mean is 1.3 inches in diameter for the canal? Otherwise the diameter for the canal would be something like 1/2 inch or so? My pi R squared math is a little rusty.

Anung Un Rama · Post by **Anung Un Rama** » Sat Apr 06, 2019 9:52 pm

Fortunately mine is not too bad.

So C=π(D) 0r 2πr

Ergo 1.3 " = 33.02 mm

thus 33.02/π =D

thus D = approx 10.5mm

So that is correct.

This is the diameter of a virgin dolls contracted and unstructured vaginal cavity opening.

This tapers to a larger slightly diameter with int cavity from about 10 mm in. So if the rated co efficient of the material stretch-ability is 455% until tearing we got capacity of 47.75mm approx diameter before failure So a war hammer with a 1.98 inch diameter or 6.2 inch circumference.

So if this is you, perhaps a mare may be more appropriate than a dolly

Anung

DollNFuture · Post by **DollNFuture** » Mon Apr 08, 2019 5:28 pm

Many thanks on the math, that sounds precise. Although I can imagine stretching any silicone material to it's max as a norm could cause quite a bit of damage to a fragile part of a doll would you agree? Maxxing her out constantly....if not exceeding constantly, truly...

Anung Un Rama · Post by **Anung Un Rama** » Tue Apr 09, 2019 1:18 am

All about conditioning and tuning a motor to normalize running under high load all day, with very good lube.

This is why there are so many oil adds and sponsorships during Nascar events :haha4:

Anung