The Doll Forum

My doll —as many of you already know— is RLSD's exclusive 142cm G-cup (made in ultra-soft TPE). I'm passing on to you the procedure that I used with a previous doll: 155 DD WM. The results here are MIND-BLOWING! In the ways of "volume," I've most likely added about 20% (which was around my controlled cut-off). Weight, realism, movement and so on; I've increased by 50 to 60%. A few notes:
* The trick with this slime product is that it wants to leak anywhere it can... Therefore, if one were to fill a doll's breast a considerable amount beyond the starting size, one would want to cap "flow-back" of product behind the incision. Also, One would want to consider the flexibility of the doll's TPE. That said, I myself only wanted a slight increase in size.
* I believe the slime product will stay fresh in cavities due to the fact that the TPE holds it's oils very well. The slime product will not dry out (even with a little exposure to air, as there is plenty of head-room in each container.
* Terrible soldering job on my part... Yes, but I'll be able to re-heat and smooth over once I'm sure that there are no leaks. I was not prepared for how much and how fast this ultra-soft TPE would burn —compared to my previous doll.
* Where are the after-pics? I'll post those later this evening —gotta clean up and make sure I don't have leaks.
* Does this procedure help small-breasted/ moderate-breasted dolls? Hell Yes it will... No more side walls touching upon squeeze, a lot more jiggle and weight (yes more weight, like real boobs).
Talk soon, stay snug. Stay tuned. I'm very very excited.

OK- Im holding my breath right now, cause all i see right now is a whole lot of hurt.. Ouch!

Damn...looks like poor angel had her wings clipped.

As a suggestion SC for melt repairs you will need some extra filler material, postion the doll lying on her front (after the boobs resets, and such that they are not compressed, and work with the iron tip from the base of the cut along Vee you are forming at the bottom of the cut until you have formed a new base layer for the entire length. Sort of like welding a vee butt weld route run and then layering...see below. (however you are also squessing or pinching the joint tofether at the same time...so ensure appropriate gloves or calipers to avoid molten tpe burns)



Then repeat the process filling as you go with extra tpe (I cut them into long slivers and apply in with tweezers) , so you are doing the repair by layering and building until backmelted to the surface flesh. One done, you can oil and heat a spoon for end smoothing. XS dolls had a good video for smoothing somewhere in the XS topics.

Ensure plenty of ventialtion two while you effect the melt repairs as the fumes are toxic.

Fantastic Plastic may also chime in here with some handy tips I may have over looked too!

Cheers And Good Luck Anung...

AUR, thank you for that!! Did you see my post regarding jiggle vids? Are those appropriate for members to post? I know manufacturers do sometimes, but wasn't totally sure.

Interesting procedure. Do you have any more pre-pictures for before and after comparison?

Here we are... She's just as awesome as can be —weighs about an extra 4 lbs, as she took 7 containers in each breast. Just an amazing feel now!!

That's some extreme surgery. They do look bigger. Makes me wonder if you could use an actual breast implant in a doll.

Here is the woman that has most greatly inspired my lust over the years... She is what inspired my want for my current doll.

I would have thought about cutting from under the breast to at least hide any scars. Not meaning to be critical, it has payed off. Just the scars on the back dude.

Unknown2

I here you brother, scars are unsightly, but I don't mind them too much for my taste since I only work with her in the dark. But with my previous doll, I did the side-of-boob technique and found that the positioning was too difficult in the ways of adding extra volume —stuff just wants to pour out as your working. I was only able to fill that particular doll to the starting volume.

Well, I personally would define "Successful" definitely not for this result, i.e. looking at a back with those huge scarfs

Anyways, did you first try out if that slime material is not harmful to TPE? I mean, in terms of aggressive behavior that over time damages the whole doll.


Edit: maybe for the next surgery you wanna try out this repair kit
http://dollforum.com/forum/viewtopic.php?f=227&t=78756
It's just awesome.

Point taken my friend And there is no doubt I'm engaging in hackery with this mod, but the feeling is totally awesome. My previous doll held this same brand/ substance for over three months without a problem... I discarded her due to other problems. But again, the slime stays viscus as long as it is not exposed to too much air. If you look at my pics, you'll see that the doll's breasts were deflated after I made cuts and squeezed air out; hence, the dolls can hold air in, and keep air out. I believe that barring my poor soldering, the technique is a great one for added volume and realism.

Good results from the front, and yes jiggle vids are just fine here.

And Dixxie Bubbles can come over to wash my car anytime....

http://www.pornhub.com/view_video.php?viewkey=133661811

Anung

Have you seen how DevilDoc inflated his K-Cup with air? The increase in volume is incredible:

http://www.dollforum.com/forum/viewtopi ... 6&start=30

Here are some pictures from the thread.

just a quick question... would it have been of benefit to less scarring if you used an oversize needle and some sort of water pump to inject, and a 2nd needle to allow air to escape until the breast cavity was full?

Just a thought.
Abe