New doll features ideas
Re: New doll features ideas
I want mine to give a good back massage.
- gogodolls
- Doll Guru
- Posts: 6450
- Joined: Thu Nov 05, 2020 1:27 pm
- Location: Maple Syrup Country
- Contact:
Re: New doll features ideas
There are a lot of great suggestions but this one is my favorite!bad-husband wrote:An ability to go from stiff skeleton to loose back to stiff.
I love falling asleep with my doll in my arms and now I imagine her body gently relaxing and molding against me.
Cheers!
Re: New doll features ideas
I’d also like a tube from the lower back that connects to the back of the vagina so I can sit her over a hole and easily pump water and then air for cleaning.
YL 160CM REGINA Head: #356. Tan TPE. Bra size: K, Fuckable Tits
Sanhui 156cm Head:#17, Platinum Silicone. White#1
WM 160D JOVI head #172, Tan TPE.
WM 170cm M-cup, Tan TPE.
Mystery 145CM~ , Black TPE Bra size: B
Several Brest toys.
Wishlist:
More Brest toys!
SM Doll 150cm L-cup
YL 150cm mega breasts
Hidoll 160cm super huge boobs titty fuck
Hidoll 160cm super huge tits big breast
Hidoll 158cm pussy breast huge boobs
Re: New doll features ideas
They are called Ultra High Molecular Weight ( UHMW ) plastics, these plastics have a lot of characteristics as steel- they can be drilled, machined, tapped (threaded), can be used in high and low temperature applications, and is considered as self lubricating when used in moving joints.
UHMW's come in square bars, rectangular bars, round bars, and sheets and plates.
This material would make a great material for skeletons that is light weight and strong.
Re: New doll features ideas
- L3aveitallblank
- Active Member
- Posts: 124
- Joined: Sun Aug 23, 2020 2:56 am
- Contact:
Re: New doll features ideas
I'd actually like that too. Accompanied with an occasional twitch or moan while they "sleep".bmar99 wrote:I was thinking a slow rhythmic inhale/exhale motion, to simulate breathing while asleep
- Fantastic Plastic
- Doll Elder
- Posts: 2358
- Joined: Mon Nov 28, 2016 9:17 pm
- Location: In a harem of beautiful love dolls!
- Contact:
Re: New doll features ideas
- L3aveitallblank
- Active Member
- Posts: 124
- Joined: Sun Aug 23, 2020 2:56 am
- Contact:
Re: New doll features ideas
Well not just vacuuming. I wouldn't mind if my girls gained a bit of ai and kept the house a bit alive while I was at work. I came up with backstories for them. If you could program some stuff into your dolls that would be cool.Fantastic Plastic wrote:Vacuuming the house while completely nude would be on my short list.
Re: New doll features ideas
Re: New doll features ideas
Second, get my Skeleton team in here! Several improvements are necessary here - fix those damn joints. Joints should not get loose, or wear out. Mechanical friction is not the way to go, work it out.
And I want bones. Hip Bones that I can feel. Rib bones I can play piano on. Done properly, our next skeleton will have a full ribcage filled with something light (which will resolve the weight issue as well) and hip bones I can feel.
There is a bonus in the paycheck of whoever can manipulate the joints to make them tight and loose at the whim of the owner. Hell, my cadillac shock absorbers adjust automatically, have for years.
Lastly we need to fix the lube issue. Cant we develop a pussy that doesn't need lube? Or one you only lube up once a month? Work that out!
Team dismissed!
ALSO TRY Reverend Jack's Anointed Snake Oil, good for cleansing stains from the body and the Soul! Step right up folks, only $5 a bottle! We got plenty to go around! Cash only please.
Aibei 158 Blue Elf, AS 157, XES 128, OR 156G, WM 160C (r), Sanhui 168 (r), WM 157B, WM 138D (Faun), Mistress 168 (r), 6YE 100 (Bubbles)
- Kaori Kusanagi
- Senior Member
- Posts: 212
- Joined: Tue Sep 22, 2020 7:18 pm
- Contact:
Re: New doll features ideas
There are purely mechanical ways to do this, but the added advantage of an electrical method is it would also (slightly) warm the doll, at least near the joints.RevJack wrote:fix those damn joints. Joints should not get loose, or wear out. Mechanical friction is not the way to go, work it out.
<snip>
There is a bonus in the paycheck of whoever can manipulate the joints to make them tight and loose at the whim of the owner.
If you don't mind a power cord from the wall (too much needed for batteries) then you could use magnetics, which could be smart or manual. Could get pretty complicated, however. Inspired by servo motors, uses permanent magnets on one side of a joint and electromagnets on the other. Engage the coils (or at least, specific ones), and increase the stiffness of a joint at a specific angle range. disengage them all for that joint and it is easy to move. No power and it is all easy to move.
Could have a squeezable switch (or set of) inside each joint area so repositioning a specific joint is all done at that joint. The switches would be normally-closed so when you engage them it turns the magnets off only while holding the switch, to act as a "latch" for the joint stiffness.
It wouldn't be cheap to do, or design, however. The purely mechanical variation is much simpler. That only needs a locking pin that is part of the bolt securing the joint, which you push in from the side of the joint you are moving, thru the "skin". This can either unlock a ratchet system in the joint, or simply decrease the friction of a joint. The former will wear much slower and require less service, but is more complex and expensive and harder to service when that does become necessary. This type of joint already exists commercially, commonly in plastic form for many folding items, but some are metal. It would likely require a custom version for these skeletons.
It is also possible to use actual servo motors, and an external control / power system (it might fit in the ribcage, but it may still need to be powered externally). It doesn't have to be robotic in nature, just a simple "hold" or "loose" state for each joint, commanded via phone app or buttons on a control panel. However, if you're already going this far....
If you go this far, you might as well give it a "real" skeleton, one that is at least vaguely human-style, at least as far as a halloween skeleton goes, or further. This would give the whole thing much more realistic poseability. It's not technically that difficult, but it is likely a lot more expensive. It may also be notably heavier than the hollow metal tube types, depending on the cost level.And I want bones. Hip Bones that I can feel. Rib bones I can play piano on. Done properly, our next skeleton will have a full ribcage filled with something light (which will resolve the weight issue as well) and hip bones I can feel.
Metal skeletons the way they are typically made now should be pretty cheap, in labor and in materials costs. The lighter plastics that are also still strong and stiff but can still be cast in a useful way toward this end, are generally more expensive (sometimes a lot more) than the metal would be, and the labor for the whole process of making the parts and assembling them is longer and costs more.
It is possible to create reservoirs inside a space that are squeezed by actions near them, that would do this. There is already such a system, including practical tested designs, in the Hot Wet Pussy thread. It's not a simple and cheap way of doing it that would be likely to be implemented in many dolls, but it could be done in other ways mostly cast right into the doll (but thus also vulnerable to damage and harder to repair).Lastly we need to fix the lube issue. Cant we develop a pussy that doesn't need lube? Or one you only lube up once a month?
- Producer V
- Apprentice
- Posts: 11
- Joined: Sun Dec 05, 2021 9:32 am
- Location: Iowa
- Contact:
Re: New doll features ideas
This is one of the things, that if solved would really make quality of life much better.
Not only will it be easier to pose your doll, but you'll also not have the problem of a limb going limp.
The idea is simple - yet figuring out how to make it happen isn't. haha
Since custom lock joints would be expensive...
...what we really need is something that we can be placed into the joint, and that increases or decreases the friction inside.
- - But it needs to be heat resistant
- - Simple & cheap
- - A spring loaded rubber pad that would press against the joint mechanisms
- - where you could somehow retract the rubber pad and control the level of friction
- - Some kind of hydraulic system
- - where you pump up the friction - and release when you need a loose joint
- - An expandable washer inserted into the joint
- - no idea how this would work (haha)
At Home:
- - 150cm ALIJIA knock off from Amazon (mistake)
- - 100cm knock off from 3rd party site (another mistake)
- - I know...
On The Way!!:
- - 172cm SYDOLL (Head #616) [w/electric hips! ]
Still Waiting On:
- - 150cm Ariel Piper-Doll
- - 160cm RidMii Avy
-
- Basic Poster
- Posts: 7
- Joined: Fri Nov 03, 2023 3:58 am
- Contact:
Re: New doll features ideas
-
- Basic Poster
- Posts: 7
- Joined: Mon Nov 27, 2023 10:47 pm
- Contact:
Re: New doll features ideas
-
- Contributing Poster
- Posts: 29
- Joined: Mon Jan 08, 2024 2:44 pm
- Contact:
Re: New doll features ideas
Much bigger loveholes, not only to avoid tearings, but also because I want to feel something soft when my hand goes in there. Not just a stupid hole big enough to hold a pencil.
Exageration could bring more realism, fucking and fisting capabilities would be perfect.
One body or face not yet on the market ?
Mature or even granny dolls are not represented in the doll industry.
Mature does not mean fat, that's the error of too many doll makers do when they talk about mature girls.
Grey hair wigs isn't the solution either.
Stop making super slim waists with big tits and ass.
What would be my perfect doll ?
A tall one, mature look, big tits, long legs and comfortable ass, lightweight (max 35kg)
Pussy and Ass options
I'd love to choose how large and deep could be a lovehole.
The next step for sexdolls : become PORNSTARS