It is currently Tue Feb 20, 2018 1:17 pm

By visiting this website and viewing the pages within, you accept and agree to be bound by and comply with the Rules Of Conduct and Terms Of Use of this website.


Official TDF Rules & TOS


Please click on either selection to view: Rules Of Conduct | Terms Of Use




 Page 2 of 2 [ 21 posts ]  
Search for:
Go to page Previous  1, 2
   
 Post subject: Re: How to dry your Fleshlight?
PostPosted: Mon Nov 28, 2016 6:22 pm 
Newbie
Newbie
User avatar

Joined: Mon Nov 28, 2016 6:06 pm
Posts: 1
Dry it with a towel and use talc/baby powder, it will be absorb most of the moisture thats left.


 Profile Send private message  
 
 Post subject: Re: How to dry your Fleshlight?
PostPosted: Tue Nov 29, 2016 3:52 pm 
Active Member
Active Member
User avatar

Joined: Mon Jul 07, 2003 12:00 am
Posts: 128
I've used FleshLights for years, never a mold issue. I find that most of the lubricants take more washing and rinsing than one might expect in order to be fully clean. I figure that you want all material out.

The large quantities of water I shake out and then put my fingers in and out a few times to pull any larger amounts out. Then, I use paper towel sheets pushed through one end to the other. Sometimes I'll put my mouth on one end and suck air through for a few minutes to remove any hint of residual moisture.

I've never found it difficult to get these dry quickly.


 Profile Send private message  
 
 Post subject: Re: How to dry your Fleshlight?
PostPosted: Tue Nov 29, 2016 7:45 pm 
Senior Member
Senior Member
User avatar

Joined: Mon Aug 01, 2016 11:52 pm
Posts: 275
Location: Dreaming in the dream of the Great Dreamer...
I personally use a ceramic fan heater on the low heat setting. Yes it takes a good 10-15 mins to get it 'almost' bone dry, but I never had any problems with this method. I also throw in some dehumidifier sachets in the storage area just for good measure.

Though I very rarely use my Fleshlights these days, I find the plastic casings to be a huge hassle to deal with and clean. I much prefer those one piece meiki's instead (the material is easier to clean too).

I have yet to test this out for myself, but if you want the ultimate drying solution for the fleshlight, I recommend you look into the 'PEET dryer':



It's not what it's designed for, but I think it'll work out just fine ;)



_____________________________
The Principles That Govern Relationships

Briffault's Law < Every Man should know of this law...
 AIM Send private message  
 
 Post subject: Re: How to dry your Fleshlight?
PostPosted: Sun Jul 23, 2017 4:20 pm 
Contributing Poster
Contributing Poster
User avatar

Joined: Mon Feb 13, 2017 11:43 am
Posts: 33
Here you go man, I tend to hang mine up to dry with a screen door hinge in the wall (bedroom has a ceiling fan to help with the airflow, plus more privacy in the bedroom versus hanging in the bathroom).
Attachment:
drying.png
drying.png [ 10.73 MiB | Viewed 586 times ]


 Profile Send private message  
 
 Post subject: Re: How to dry your Fleshlight?
PostPosted: Thu Jan 04, 2018 6:06 am 
Contributing Poster
Contributing Poster

Joined: Mon Dec 25, 2017 12:42 am
Posts: 20
Location: phoenix arizona USA
well, I have 3 Fleshlights here. The best way I have found to dry them is to turn them inside out (as much as possible), then towel dry them and then sprinkle corn starch where ever I can. Sometimes, if this proves impractical, I will spray in some rubbing alcohol (let it run down through the fleshlight and into the sink), then hang dry. So far, no mold growth and no funky oders.

one other thing I haven't tried yet. the room mate has an air compressor (the type used for airbrushing, airing up tires and inflatible furniture). It can hold about 150 psi, so spraying some air up through the toy should blow out any water.


 Profile Send private message  
 
 Post subject: Re: How to dry your Fleshlight?
PostPosted: Wed Jan 10, 2018 9:31 am 
Basic Poster
Basic Poster
User avatar

Joined: Wed Jan 10, 2018 7:31 am
Posts: 6
So far I've been drying with a towel, I also take a bit of the moisturing from inside using my fingers and blowing. Then after some minutes I insert my finger again to check if it's still wet. If it's enough dry then I'll apply the repair powder/corn starch and job done.
Now I've got some bigger sex toys and this method is a pain, so I may check some other way to dry inside them.


 Profile Send private message  
 
Display posts from previous:  Sort by  
 Page 2 of 2 [ 21 posts ]  Go to page Previous  1, 2


Who Is Online

Users browsing this forum: No registered users and 22 guests

Chatting users:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum