Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
-
- Contributing Poster
- Posts: 46
- Joined: Wed Apr 04, 2018 8:54 pm
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
- The Messenger
- Doll Elder
- Posts: 2385
- Joined: Tue Mar 06, 2018 9:16 pm
- Location: california
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Yeah, I have the same experience as Terabyte. And I use the same technique to get my 163 H cup to stand.terabyte wrote:Those curves are to die for! She is stunning, and she looks absolutely smoking hot with the blonde hair and glasses!Gordonis wrote:...Later has arrived. The morning after specifically. There's a small tear in the vagina that could potentially turn into a big tear. I basically noticed the tpe splitting when I had her spread open to put in the insert. And then during fun time when I had her spread eagle the tear got slightly bigger unbeknownst to me. The lights were low to create atmosphere. I had her arms up over her head several times throughout as well and noticed two small tears on either side of the seem in her armpit. She is heavy but manageable for myself. I've decided going forward that spread eagle or arms over the head are no longer options as any further stress on these areas could result in further damage. In my research leading up to my purchase I'd read several horror stories of TPE tearing almost right away. So I was prepared for this. I do not regret my purchase in any way. In fact I'm still very happy with Jaz-Lyn. So glad she's come into my life. I haven't done any shopping for her yet and only have the pink nighty that they shipped with her. So I'll take some pics later on today with her in that.[/b]
I've also learned getting the larger dolls to stand can be tricky, especially if they have large breast and booty's. I have a 170 and I can get her to stand however you have to make sure the foot screws are set right and her leg/knee bends are straight out. Easiest way for me is to lay the doll on the bed and bend the legs over the edge, if you can "kick" the leg straight up you should be good, if not you will have to rotate the knee joint. The larger dolls also usually need a 3rd point of contact to balance against as I don't think they can free stand, I could be wrong though.
She's good as long as there's a 3rd point of contact to keep her balanced.
Though with that body, horizontal is still my favorite position for her!
-
- Senior Member
- Posts: 295
- Joined: Thu Feb 08, 2018 9:46 pm
- Location: Alberta Canada
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
-
- Senior Member
- Posts: 295
- Joined: Thu Feb 08, 2018 9:46 pm
- Location: Alberta Canada
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
-
- Senior Member
- Posts: 295
- Joined: Thu Feb 08, 2018 9:46 pm
- Location: Alberta Canada
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Going to follow the steps as shown here: https://www.youtube.com/watch?v=wfEHMJtCu58
Any final tips or advice would be greatly appreciated. Feeling really nervous and out of my depth but still ready to face the challenge. Going into this (being a doll owner), I knew there would be obstacles to overcome I just didn't think they would be so soon.
-
- Senior Member
- Posts: 295
- Joined: Thu Feb 08, 2018 9:46 pm
- Location: Alberta Canada
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
-
- Senior Member
- Posts: 295
- Joined: Thu Feb 08, 2018 9:46 pm
- Location: Alberta Canada
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Okay, thank you. The device you got at home depot, do you have any concerns of it rusting? Do you also use it to dry out the orifices? Just curious as I am considering getting my next doll as "fixed" and due to my living conditions, I am not able to utilize an aquarium pump. Thank you.Gordonis wrote:I cleaned the area with isopropyl alcohol and had a piece of cloth soaked with it as well that I used to constantly clean the shaping tool after each use.
- Chuck Norris
- Doll Mentor
- Posts: 1145
- Joined: Sat Mar 24, 2018 9:16 am
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
-
- Senior Member
- Posts: 295
- Joined: Thu Feb 08, 2018 9:46 pm
- Location: Alberta Canada
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Damage to her feet happened within the first 5 days of moving her around, trying on clothes for posing and such. The damage to her armpits and vagina happened on the first night.pat_the_brat_1 wrote:If I understand this correctly, the damage to her feet,armpit etc happen during the first month of having her?
- Chuck Norris
- Doll Mentor
- Posts: 1145
- Joined: Sat Mar 24, 2018 9:16 am
- Contact:
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Thanks for the info
Re: Jaz-Lyn has been ordered!! WM 163CM Hcup #200 Head
Unscrew the screws a bit so when you put her up to stand ,the screws are the ones that are touching the floor and not her skin.Gordonis wrote:Damage to her feet happened within the first 5 days of moving her around, trying on clothes for posing and such. The damage to her armpits and vagina happened on the first night.pat_the_brat_1 wrote:If I understand this correctly, the damage to her feet,armpit etc happen during the first month of having her?
On Monday i will have a set of screws(M6x20) with wider head to try if they can protect her feet better.
-
- Doll Advisor
- Posts: 669
- Joined: Mon Apr 16, 2018 4:23 pm
- Contact: